The corrosion behavior and mechanism of X65 steel induced by iron‐oxidizing bacteria in the seawater environment

The corrosion behavior and mechanism of iron‐oxidizing bacteria (IOB) on X65 steel in seawater are studied. This study uses the methods of weight loss, electrochemical measurements, and surface analysis. The results show that the IOB increases the corrosion damage degree of steel. Pittings are observed in the medium with IOB. The potentiodynamic polarization curves show that the anodic reaction rate is accelerated in the corrosion process of IOB. The synergies in corrosion between the metal surface, abiotic corrosion products, and bacterial cells, and the pitting corrosion mechanism of X65 steel are discussed.     

熔融制样-X射线荧光光谱法测定硅铁中硅磷锰铝钙铬

熔融制样-X射线荧光光谱法(XRF)测定硅铁合金样品,需重点解决样品前处理中合金样品侵蚀铂-黄坩埚的难题。硅铁样品以四硼酸锂-碳酸锂预氧化剂在石墨垫底瓷坩埚中高温预氧化熔融后,再将熔融物转移至铂-黄坩埚中,用四硼酸锂熔融制成玻璃熔片,实现了熔融制样-X射线荧光光谱法对硅铁合金中硅、磷、锰、铝、钙、铬的测定。实验讨论了预氧化熔融的熔剂体系及氧化方法、试样与熔剂的稀释比,结果表明,试样与熔剂以1∶35的稀释比,以10滴300g/L碘化钾溶液为脱模剂,在1100℃熔融30min,熔融制得的玻璃片均匀、透明、无气泡,符合测定要求。用具有浓度梯度的系列硅铁有证标准样品制作校准曲线,各待测元素校准曲线的线性相关系数均大于0.9995。方法应用于硅铁合金实际样品中硅、磷、锰、铝、钙、铬的测定, 结果的相对标准偏差(RSD,n=11)在0.1%~5.8%之间;正确度试验表明,硅铁标准样品的测定结果与认定值相符,硅铁实际样品的测定结果与国家标准方法测定值一致,能满足常规分析要求。     

Evidence of nano-galvanic couple formation on in-situ formed nano-aluminum amalgam surfaces for passivation-bypassed water splitting

Reaction of Al metal with water is a well-known technique for large scale production of hydrogen. However, this method suffers from kinetic limitations due to formation of a passivation layer on Al, preventing optimal operations. Using high resolution Scanning Kelvin Probe Force Microscopy (SKPFM), we show the origin of formation of 'nano-galvanic couple' on in situ formed nano-aluminum amalgam surfaces in a water splitting system; passivation based limitations are completely bypassed in this approach. Furthermore, they offer an opportunity to beneficiate and recover mercury in contaminated water. The nano-galvanic corrosion due to substantial lateral variation in surface contact potential is responsible for the observed high throughput of hydrogen production (720 mL/min per 0.5 g Al salt). It may be noted that this process fares better than in situ prepared nano-Al based hydrogen production, wherein 600 mL/min of hydrogen is obtained for 0.5 g Al salt. Investigations using Cyclic Voltammetry (CV) and Electrochemical Impedance Spectroscopy (EIS) provide evidence for passivation-bypassed hydrolysis and favourable kinetics for in situ derived nano-AlHg hydrolytic agents (when compared to nano-Al). This study, to the best of our knowledge, reports the first direct proof of nano-galvanic couple formation on in-situ prepared nanoaluminum amalgam surface; paving a direct way to overcome the long standing passivation problem in Al hydrolysis. It is found that the hydrogen production rate and standard deviation (SD) of the contact potential of nanoaluminum amalgam are directly related to the rate of addition of the reducing agent, offering an opportunity for kinetic control for the in situ hydrolytic process.     

300M超高强钢在中性盐雾环境中的腐蚀行为及机制

摘要：为了研究300M超高强钢在中性盐雾环境中的腐蚀行为及腐蚀机制，采用失重法，宏观、微观腐蚀形貌分析，三维表面轮廓分析及电化学分析的研究方法，来表征腐蚀实验现象并进行分析。结果表明：300M超高强钢在中性盐雾环境中的腐蚀产物为FeOOH、Fe2O3、Fe(OH)3和Fe3O4；腐蚀速率随着腐蚀时间逐渐降低，腐蚀后期（72h）腐蚀速率降低50%；腐蚀初期以点蚀为主，点蚀坑通过横向扩展，逐渐发展为后期的均匀腐蚀，腐蚀表面形貌呈沟壑状；外腐蚀层对基体的保护能力很弱，Cr元素在锈层靠近基体的一侧偏聚使内腐蚀层具有一定的抗腐蚀性。     

Theoretical and experimental studies of a new aniline derivative corrosion inhibitor for mild steel in acid medium

4-Chloro-N-(pyridin-2-ylmethyl)aniline (CPYA) was synthesized by a simple and inexpensive method and tested as a corrosion inhibitor in acid medium for mild steel by using gravimetric studies and electrochemical measurements. An average maximum efficiency of 96.0% was achieved at 4.59 mmol/L. Corrosion kinetic and thermodynamic parameters were also analyzed. Surface analyses (atomic force microscopy and scanning electron microscopy) show that protection is enabled by adsorption on the metal, forming a film. Quantum chemical calculations were performed to access information regarding the molecular structure in the corrosive medium and to support interpretation of the results obtained by experimental methods.     

Corrosion behaviour and mechanism of 6082 aluminium alloy in NaCl and Na2SO4 etchants

The corrosion behaviour of 6082 aluminium alloy was studied by measuring the electrochemical impedance spectra and electrode polarization curves. After the electrochemical tests, a microstructural analysis of the samples was conducted by using optical microscopy and electron scanning microscopy techniques to determine the corrosion mechanism. The results show that the Nyquist plot of the electrochemical impedance data in the NaCl solution consists of high- and low-frequency capacitive impedance loops. When ions are added to the NaCl etchant, the Nyquist plots of the electrochemical impedance data are composed of two different curves: a high-frequency capacitive impedance loop and a low-frequency inductive impedance loop. The corrosion current density increases with increasing concentration, and as a result, the corrosion resistance of the aluminium alloy decreases. The microstructures of 6082 aluminium alloy consist of Mg₂Si secondary particles in a large α-Al matrix. Pitting corrosion initially occurs at the boundary between the matrix and secondary particles because the electrode potentials of the matrix and secondary particles are different. Then, corrosion paths develop along the network-like grain boundaries, and finally, massive network-like corrosion occurs throughout the entire alloy.     

Microstructure and corrosion behaviors of FeCrNiBSiMox stainless steel fabricated by laser melting deposition

In this paper, FeCrNiBSiMo_x (x = 1.0, 1.5, 2.0, 2.5) stainless steels were successfully prepared using a laser melting deposition technology, with the aim to investigate the effect of Mo content on microstructure and corrosion behaviors. The results showed that the as-deposited specimens were composed mostly of α-Fe and a small amount of (Cr, Mo)₇C₃, and (Cr, Mo)₇C₃ existed in the inter-dendritic (ID) region. As the Mo content increased, grain refinement could be clearly observed, and the area of the ID region increased from 27% to 54%. The low-angle boundaries accounted for 60–70% of the grain boundaries of the as-deposited specimens. Increasing the content of Mo improved the microhardness of the as-deposited specimens from 652 HV to 813 HV. The corrosion current density of the as-deposited specimens with the Mo mass fractions of 1.0%, 1.5%, 2.0%, and 2.5% were 1.37 × 10⁻⁶, 1.02 × 10⁻⁷, 6.19 × 10⁻⁷, and 3.06 × 10⁻⁷ A/cm², respectively. The as-deposited specimen with Mo content of 1.5% had lower cumulative erosion loss and erosion loss rate than other as-deposited specimens. The FeCrNiBSiMo_x (x = 1.5) specimen exhibited excellent resistance to electrochemical corrosion and cavitation erosion.